What a leatherette bracelet & bangle box is — and what it has to do
A bracelet or bangle box holds a round piece in shape with a cushioned bar or ring, so a bangle does not flatten or a chain bracelet does not tangle. The insert is shaped to the diameter of the pieces you sell.
For a bangle box the leatherette exterior gives shelf durability while a soft cushion inside protects the bangle's polish; a PU-covered cushion would mark a high-polish bangle over time.
How a leatherette bracelet & bangle box is built inside
A bangle box is built around a C-shaped or cylindrical cushion: the bangle slides over the cushion and is held open in its true round. A chain bracelet uses a long box instead — a full-length pad with a central slot into which the bracelet is laid, or a removable cylindrical pillow it wraps around.
Fit. The cushion diameter is cut to the inside diameter of the bangle — usually 60–70 mm — so a rigid bangle sits snug without being stretched; for hinged bangles the cushion is slightly smaller so the hinge is not stressed when closed.
In leatherette. A PU-covered insert has almost no give, so it is cut to the finished dimension and the covering is turned under and glued flat on the reverse; any excess thickness at a fold shows as a bump under the piece. Where a PU exterior meets a soft lined interior, the join sits inside the lid rim so the customer sees a clean edge.
Formats we make: C-cushion bangle box · round bangle box · long slotted bracelet box · removable-pillow box · cuff box with an open-front cushion.
Why leatherette (pu) for bracelet and bangle boxes
Leatherette — a fine PU with a leather-like grain — is the modern jeweller's workhorse: clean, hard-wearing and consistent from box to box. It takes a hot-stamped logo crisply and resists everyday marks.
PU is wrapped and turned over the shell edge, so the corner fold is the quality tell: we mitre and tuck corners rather than bunch them, and use a thinner PU on tight radii so the grain does not stretch and go pale. Grain, gloss level and hand-feel are all specified — a soft-touch matte PU and a saffiano-grain PU behave very differently under a hot-stamp.
PU is colour-stable and matches to Pantone references closely, which makes it the safe choice when several boxes in a range must match across production runs.
It suits branded retail ranges, e-commerce brands shipping many orders, and anyone who needs a crisp foil logo.
Specification at a glance
| Piece held | Bracelet |
|---|---|
| Insert | A c-shaped bangle cushion, or a long slotted pad / removable pillow for chain bracelets |
| Fit detail | The cushion diameter is cut to the inside diameter of the bangle — usually 60–70 mm — so a rigid bangle sits snug without being stretched; for hinged bangles the cushion is slightly smaller so the hinge is not stressed when closed. |
| Typical external size | Bangle boxes are commonly 90–100 mm square and 40–50 mm deep; long bracelet boxes run 180–220 mm by 50–60 mm. |
| Formats | C-cushion bangle box · round bangle box · long slotted bracelet box · removable-pillow box · cuff box with an open-front cushion |
| Exterior | Leatherette (PU) — black, white, tan, camel, burgundy, navy, blush, deep purple |
| Hand feel | Crisp, firm, consistent — reads as a considered retail brand |
| Insert construction | Pu-wrapped pads with a soft lined slot |
| Interior lining | Velvet, microfibre suede or satin, in a matching or contrast colour |
| Logo | Leatherette is the best surface for a hot-stamped logo in gold, silver, rose gold or a blind (colourless) deboss. Foil sits cleanly in the grain and holds its edge over years of handling. |
| Closure | Hinged lid with a snap or magnetic catch; ribbon or clasp on travel formats |
| Shell route | Ready tooling library (no mould charge) where a standard size fits; fully custom dimensions on a wooden shell where it does not |
| Sample | A physical pre-production sample is made and approved before any bulk run |
| Quantity & lead time | Quoted per project — structure, materials and any tooling decide both; tell us the quantity you have in mind |
Two ways to get the size you need
Every box starts with the piece, and the piece decides the shell route:
- Ready tooling library. We hold a range of existing moulded shells in the common jewellery-box sizes. Where one of these fits your piece, there is no mould charge and the box is faster to produce — you choose the finish, lining and logo on a proven shell.
- Fully custom dimensions. Where no standard shell suits — an unusual bracelet, a signature proportion, a matching family of sizes — we build the box on a wooden shell cut to your dimensions and finished in lacquer or wrapped in your chosen material.
We will tell you which route fits your brief before quoting, so there are no surprises on tooling or timing.
What we check on every leatherette bracelet & bangle box
Before a sample is sent, and again on every bulk run, each leatherette bracelet & bangle box is checked against the same points — the insert is PU-wrapped pads with a soft lined slot, so the fit checks below are read against that construction:
- bangle sits round on the cushion, not flattened
- cushion clears the hinge on a hinged bangle
- chain bracelet lies flat in the slot with the clasp tucked
- cushion is firmly seated and does not rock in the cavity
- the grain runs continuously across lid and base with mitred corners
- lid and base outlines match exactly when closed — same footprint, same corner radius
- insert fills the cavity with no gap to the wall; walls are an even thickness
- leatherette panels have continuous grain or nap with straight, even seams
The most common faults we see in bracelet and bangle boxes bought elsewhere are a cushion cut to the outside diameter (the bangle floats), a slot too shallow for a heavy link bracelet, and a lid that touches the top of the bangle. Each of those is a specification decision, and we make it with you before the sample.
Made to your brand
Your size, your lining, your colour, your logo. Leatherette is the best surface for a hot-stamped logo in gold, silver, rose gold or a blind (colourless) deboss. Foil sits cleanly in the grain and holds its edge over years of handling. PU wipes clean and does not fade in a lit window display, so it suits stock that sits on a shop shelf.
You approve a physical sample before bulk, and the bulk order is held to the sample you approved — the same leatherette, the same insert, the same logo position.
How ordering works
Send us the bracelet dimensions (or the piece itself), the quantity you have in mind, your logo artwork and any colour references. We confirm the shell route and the insert, quote one clear all-in price, and make a pre-production sample for you to approve. Production follows the approved sample. Quantities and lead times are agreed per project rather than fixed, because structure, materials and any tooling decide both.
Why Chung Ngai
Chung Ngai is a manufacturer and supplier of jewellery and watch packaging, Hong Kong owned and managed since 1971. We build and check boxes by hand, quote one transparent price, and hold every bulk run to the approved sample. For leatherette bracelet and bangle boxes made to your brand, that consistency is what keeps jewellers re-ordering.