What a lacquered wood earring box is — and what it has to do
An earring box holds a pair neatly with slots, a flap or a foam pad, so studs and drops stay together and face forward. Small and precise, it is one of the most-used boxes in any jewellery range.
Wood earring boxes are chosen for high-value pairs — a lacquered shell with a pierced velvet pad — where the box is expected to live on a dressing table.
How a lacquered wood earring box is built inside
The base pad carries two pin holes or two short slits set a fixed distance apart; the earring posts push through and the pair stands upright, side by side. For drops and hoops a small covered flap replaces the pad — the posts go through the flap and the drops hang free below it, so nothing is crushed when the lid closes.
Fit. Pin holes are pierced, not cut, so the pad grips a standard 0.8 mm post; the two holes sit 15–20 mm apart so the pair reads as a pair without touching.
In lacquered wood. Inside a lacquered shell the insert sits in a routed recess rather than against a wrapped wall, so the insert is cut to the recess and the lining is turned into the gap — the lacquered rim stays clean and the pad cannot lift. Shell walls are thicker than a moulded box, which is why a wood box feels heavier for the same internal size.
Formats we make: stud box with a pierced pad · slit pad for lever-backs · flap box for drops and hoops · deep box for chandeliers.
Why lacquered wood for earring boxes
A lacquered wood box is a keepsake in its own right. The shell is built up in layers and hand-sprayed to a deep, even shine, giving a weight and quality that customers keep long after the sale.
Because a wooden shell is cut rather than moulded, the external dimensions are free — this is the route we recommend when a piece needs a size that no ready tooling matches. Lacquer is applied in several coats with sanding between, so the finish depth and gloss level (high gloss, satin or matte) are part of the specification.
Any lacquer colour can be matched, with piano black, deep burgundy and warm walnut the most requested; interiors are lined in velvet or suede to protect the piece against the hard shell.
It suits higher-value pieces, collectors, watch brands and gifting where the box is expected to be kept and reused.
Specification at a glance
| Piece held | Pair of earrings |
|---|---|
| Insert | A twin-hole or twin-slit pad, or a covered flap for drops and hoops |
| Fit detail | Pin holes are pierced, not cut, so the pad grips a standard 0.8 mm post; the two holes sit 15–20 mm apart so the pair reads as a pair without touching. |
| Typical external size | Most earring boxes are 55–75 mm square and 30–40 mm deep; drop-earring flap boxes go deeper — 45–55 mm — to give the drops room to hang. |
| Formats | stud box with a pierced pad · slit pad for lever-backs · flap box for drops and hoops · deep box for chandeliers |
| Exterior | Lacquered Wood — piano black, burgundy, walnut, ivory, navy, forest green |
| Hand feel | Heavy, lacquered, keepsake — the box stays on the dressing table |
| Insert construction | Lined pads set into a routed recess |
| Interior lining | Velvet, microfibre suede or satin, in a matching or contrast colour |
| Logo | On lacquer the logo is normally printed or foil-stamped on the lid, or set as a metal plate; a debossed logo is also possible under the lacquer for a subtle 'in the surface' look. |
| Closure | Hinged lid with a snap or magnetic catch; ribbon or clasp on travel formats |
| Shell route | Ready tooling library (no mould charge) where a standard size fits; fully custom dimensions on a wooden shell where it does not |
| Sample | A physical pre-production sample is made and approved before any bulk run |
| Quantity & lead time | Quoted per project — structure, materials and any tooling decide both; tell us the quantity you have in mind |
Two ways to get the size you need
Every box starts with the piece, and the piece decides the shell route:
- Ready tooling library. We hold a range of existing moulded shells in the common jewellery-box sizes. Where one of these fits your piece, there is no mould charge and the box is faster to produce — you choose the finish, lining and logo on a proven shell.
- Fully custom dimensions. Where no standard shell suits — an unusual pair of earrings, a signature proportion, a matching family of sizes — we build the box on a wooden shell cut to your dimensions and finished in lacquer or wrapped in your chosen material.
We will tell you which route fits your brief before quoting, so there are no surprises on tooling or timing.
What we check on every lacquered wood earring box
Before a sample is sent, and again on every bulk run, each lacquered wood earring box is checked against the same points — the insert is lined pads set into a routed recess, so the fit checks below are read against that construction:
- both earrings stand upright and face forward at the same angle
- posts are gripped by the pad and do not fall out when the box is tilted
- drops hang free of the base when the lid is closed
- the pair is centred in the box, not pushed to one side
- the lacquer is even across all faces with no dust or orange peel at the corners
- lid and base outlines match exactly when closed — same footprint, same corner radius
- insert fills the cavity with no gap to the wall; walls are an even thickness
- lacquered wood panels have continuous grain or nap with straight, even seams
The most common faults we see in earring boxes bought elsewhere are holes punched too large for fine posts, a pad too thin to grip, and a flap box too shallow so the drops touch the base. Each of those is a specification decision, and we make it with you before the sample.
Made to your brand
Your size, your lining, your colour, your logo. On lacquer the logo is normally printed or foil-stamped on the lid, or set as a metal plate; a debossed logo is also possible under the lacquer for a subtle 'in the surface' look. Lacquer is durable but shows fingerprints on high gloss — a satin finish is the practical choice for display boxes that are handled daily.
You approve a physical sample before bulk, and the bulk order is held to the sample you approved — the same lacquered wood, the same insert, the same logo position.
How ordering works
Send us the pair of earrings dimensions (or the piece itself), the quantity you have in mind, your logo artwork and any colour references. We confirm the shell route and the insert, quote one clear all-in price, and make a pre-production sample for you to approve. Production follows the approved sample. Quantities and lead times are agreed per project rather than fixed, because structure, materials and any tooling decide both.
Why Chung Ngai
Chung Ngai is a manufacturer and supplier of jewellery and watch packaging, Hong Kong owned and managed since 1971. We build and check boxes by hand, quote one transparent price, and hold every bulk run to the approved sample. For lacquered wood earring boxes made to your brand, that consistency is what keeps jewellers re-ordering.